Fitting Formula

Inspire offers a variety of prescriptive approaches for fitting hearing aids. These approaches can be categorized as being either Linear or Non-Linear in nature. Linear fitting formulas were designed to prescribe gain for hearing aids with fixed gain and frequency responses across input levels. Non-Linear fitting formulas prescribe different amounts of gain depending upon input level and were developed to fit wide dynamic range compression hearing aids.

The Non-Linear and Linear fitting formulas available within Inspire are described below. Only the fitting formulas selected via Target Preferences are available in the drop down list from most Fitting and Advanced Tools screens.

• e-STAT (default) - e-STAT is a proprietary fitting algorithm. It originated as a less compressive version of NAL-NL1 and has since been empirically optimized over the course of several years based on the preferences of real patients wearing Starkey hearing aids. e-STAT is tailored to Starkey's compression architecture with target gains defined at the system’s critical kneepoints. Also unique to e-STAT is the ‘minimize vent interaction’ feature which changes target gain based on vent size. The goal of this feature is to reduce the potential for audible artifact by minimizing the region over which amplified sound and direct path sound are at about the same level. Expect e-STAT to provide a good starting point from which further fine tuning adjustments may be needed.
• DSL v5 (DSL m[i/o]) - Specific objectives of DSL v5 include:
• • Avoidance of loudness discomfort during hearing aid use
  • Hearing aid prescription that ensures audibility of important acoustic cues in conversational speech as much as possible
  • Prescription of hearing aid compression that is appropriate for the degree and configuration of the hearing loss, but that attempt to make a wide range of speech inputs available to the listener
  • Accommodation for the different listening requirements within quiet and noisy listening environments
  • Widely recognized fitting formula for pediatrics

A detailed description can be found at http://www.dslio.com.

Real Ear Aided Response (REAR) pure-tone DSL v5 targets that are generated in Inspire can be expected to closely match the DSL v5 stand alone version. Slight discrepancies can be accounted for by the fact that Inspire always uses soft speech compression thresholds whereas DSL v5 may prescribe slightly different compression thresholds.

• NAL-NL1 - The established NAL-R procedure (Byrne & Dillon, 1986) aims to produce all bands of speech at equal loudness. For people with profound hearing loss, research with linear amplification shows us that a systematic departure from equal loudness is necessary: High frequency bands are made less loud than the others, because of the diminished contribution of the high frequency bands to intelligibility, even when the information within those bands is audible. This departure from equal loudness is the basis of the NAL-RP prescription procedure (Byrne, Parkinson and Newall, 1990). The NAL-NL1 procedure is an extension of the NAL-RP formula, based on the following assumptions:
• • The relative loudness of different speech bands should be such as to maximize speech intelligibility
  • The hearing aid patient should perceive speech to be no louder than that which a normal hearing person would perceive

  A detailed description can be found at http://www.nal.gov.au/nal-software_tab_nal-nl-1.shtml.

• NAL-NL2 - This formula maintains the same aim as NAL-NL1, which is to make speech intelligible and overall loudness comfortable. In general, NAL-NL2 provides more gain in low and high frequencies, and less gain through the mid-frequency region. The National Acoustics Laboratory reports that NAL-NL2 will provide better speech intelligibility without increasing loudness.

A detailed description can be found at http://www.ncbi.nlm.nih.gov/pmc/articles/PMC4040825/.

• BERGER - This linear formula overlays on the hearing threshold level a gain-frequency response, which mirrors the speech spectrum. Berger is designed for use with linear and compression limiting hearing aids.
• NAL-R - The goal of this linear prescriptive formula is to amplify speech so that all frequency bands contribute equally to its loudness. Modifications for listeners with severe to profound hearing loss are also included.

A detailed description can be found at https://www.nal.gov.au/.

• WFA - This linear formula provides more high frequency gain and is a proprietary fitting formula (William F. Austin) that's only available in Inspire.
• Music - This formula is only available with the Music memory in Picasso, Muse iQ, SoundLens Synergy iQ, Muse, or SoundLens Synergy products and cannot be selected. It was developed specifically for music and music listening. It restores both overall loudness of loud music with flat gain, and audibility of soft music with shaped, compressive gain.
• e-STAT AI - This formula is based on NAL-NL2 and was developed specifically for Spatial Hearing, therefore, it's only available in Picasso and Muse iQ CIC and Picasso and SoundLens Synergy iQ IIC products if this fitting formula was selected and/or Spatial Hearing was enabled in Inspire version 2019.0 or earlier.