Verification Report

The Verification Report prints data for up to 6 captured curves on a graph based on real ear response. In addition, details regarding the hearing aid's configuration, audiogram, and adaptive features for the selected memory print on the report. If fitting binaurally, each hearing aid prints on its own page. Based on the Report Header selected via Reports Preferences, either the manufacturer's logo, company's logo, or customized text prints in the top left hand corner of the report. This report is only available if at least one curve was captured via Speech Mapping, Integrated Speech Mapping, or select Fitting or Advanced Tools screens during the current or retrieved session.

  1. Connect and select the desired hearing aid(s) to report via Get Started.

  2. Click on the Read Device Settings or Load a Previous Session radio button and then click .

  3. Click Advanced Tools from the Left Navigation Menu.

  4. Click Speech Mapping from the Left Navigation Menu or click Speech Mapping from select Fitting or Advanced Tools screens.

    Tip:  To launch Integrated Speech Mapping, clickIntegrated Speech Mappingfrom the Speech Mapping screen.

  5. Capture curves if not captured previously.

  6. Click on the specific memory to print, if applicable.

  7. Check the desired captured curves to print, if applicable.

    Note:  Only the captured curves checked View print on the report.

  8. Check the desired display curves to print, if applicable.

    Note:  Only the curves (e.g., Audiometric Thresholds, Soft Target/Response, etc.) checked print on the report.

  9. Click File from the Menu Bar.

  10. Click Print to print and/or preview the report.

    Tip:  Click  on the Inspire Toolbar to print and/or preview the report.

  11. Click Verification Report.

    Note:  Verification Report is only enabled if at least one curve was captured and checked View via Speech Mapping or select Fitting or Advanced Tools screens during the current or retrieved session and the current memory selected is not Disabled.

  12. Click Print or Print Preview.

    Note:  If more than 6 captured curves were checked View via Speech Mapping or select Fitting or Advanced Tools screens, a message that only the 6 most recent captures will print on the report. Click Continue to print the 6 most recent captures or click Cancel to cancel the report and select the 6 desired captures to print. If real-time view Input + Gain was selected when the curve was captured, both an input and output curve were created, therefore, it's listed as 1 capture but is counted as 2.
     
    Tip:  Click Cancel to cancel the report and close the Print screen.

  13. If Print was selected, change any print settings if desired and click Print. If Print Preview was selected, navigate or print the report using the options on the Print Preview Toolbar.

    Verification Report Description
    Report Header Manufacturer's logo, company's logo, or customized text. Prints based on the Report Header selected via Reports Preferences.
    Verification For Patient's name.
    Right/Left Ear Right/left hearing aid's product family, circuit, and style.
    Serial # Right/left hearing aid's serial number.
    FW Right/left hearing aid's firmware version.
    Date of Birth Patient's date of birth.
    Session Date of the current or retrieved session.

    Real Ear
    Average RECD, Measured RECD, HA1/Foam Plug RECD, HA2/Foam Plug RECD, HA1/Earmold RECD, HA2/Earmold RECD, Average REUG, Soundfield 0° REUG, Soundfield 45° REUG, and/or Soundfield 90° REUG RECD and/or REUG values predicted, measured, or entered via DSL v5 Patient Preferences.
    Real Ear Graph (only prints if the hearing aid supports Live Real Ear or Integrated Real Ear) For hearing aids that support Live Real Ear, only the display options selected via Live Real Ear print on the graph.
    Graph Legend (only prints if the hearing aid supports Live Real Ear) Describes the curves and shaded regions on the graph.

    Configuration
    Matrix, Fitting Formula, Acoustic Options, and/or Switch Configuration/Push Button Configuration/Sweep Technology Mode Indicates the current configuration of the hearing aid's features. Only the features supported print.

    Audiogram
    Audiogram Graph Office system, hearing aid, or In-situ air conduction, bone conduction, and UCL points.
    Audiogram Legend Identifies the symbols on the audiogram.

    Memory and Current Output/Gain/Slope
    Speech Mapping Captured Graph Regardless of the graphical view currently selected, the fitting graph prints based on Real Ear Response output and Input Type: Speech. Only the curves (e.g., captures, Audiometric Thresholds, Soft Target/Response, etc.) checked via Speech Mapping or select Fitting or Advanced Tools screens print on the report.
    Graph Legend Identifies the curves, shaded regions, and captures on the graph.
    Adaptive Features
    Feedback Canceller, Directionality, Quiet, Wind, Machine Noise, Speech and Noise/Noise, and/or Music Indicates the current setting of the memory's features. Only the features supported print.
    Target (Hz) (only prints if at least one display, except Audiometric Thresholds, was selected)
    Soft Target (dB SPL), Moderate Target (dB SPL), Loud Target (dB SPL), and/or Max Output (dB SPL) Target values per frequency. Only the values (e.g., Soft Target/Response, Max Output, etc.) checked via Speech Mapping or select Fitting or Advanced Tools screens print on the report. The target levels print based on the Target Levels selected via Target Preferences.
    Capture Average (Hz)
    Curve Label and View Actual (single capture) or average (over time capture) values per frequency. The curve label, which can be customized, prints the color, memory (in parenthesis), and time of the capture. The view selected (Input + Gain, Input, or Output) when the curve was captured also prints. If Input + Gain was selected, one row per view prints.

  14. If Print Preview was selected, click X on the Title Bar to close.

  15. Click Cancel to close the Print screen.